HPG 100 Value Vibratory Truss Screed, Power Section

Item Number: 0008293

Easy to assemble and adjust screeds offer high performance and jobsite productivity

Vibratory truss screeds are designed for precise strike-off and consolidation of concrete surfaces up to 25 cm/10 inches thick where critical flatness is desired. The bolted construction throughout the screed sections allow for fast assembly without special tools. The T-bolt adjuster provides quick, precise adjustments for flat, crowned or inverted strike-off.

  • Bolted construction throughout screed sections allows fast assembly without special tools.
  • Wide span up to 75 feet (heavy-duty) for large floor pours.
  • T-bolt adjuster provides quick, precise adjustments for flat, crowned, or inverted strike-off.
  • Winch system consists of two cranks located on same end of screed for one person operation.
  • Connector plate with greaseable flange bearing provides rigidity for even vibration and fast assembly of sections.
  • Eccentric weights located near shaft bearings prevent shaft whip and extend bearing life.
  • Lightweight, high strength aluminum truss for reduced weight and easy machine handling.
  • Fully self-contained unit will run on any form, such as pipe, wood, block or metal.
  • Accessories available to meet recessed pour or wall slider requirements. Outrigger attachment adds one foot without disassembly.

Standard Package – HPG 100
Above package includes operator's manual and parts book.

Description Metric Imperial
Length x width x height 3,1 mm 10.0 in
Beam width 355 mm 14 in
Height 475 mm 18.75 in
Weight 92 kg 204 lb
Engine Type air-cooled, 4 cycle, single cylinder, gasoline engine Honda
Operating speed 3.600 1/min 3,600 rpm
Piston displacement 242 cm3 14.8 in3
Horsepower* 6 kW 8 hp
Fuel tank capacity 6 l 6.4 US qt
Fuel consumption 2 l/h 2.1 US qt/h
Eccentric shaft VPM 2.650 1/min 2,650 rpm

Specifications may change due to continuous product development.
* Actual power output may vary due to conditions of specific use.

Accessories are not included with machine purchase.

Recesser
0115714
This recessing attachment makes below-grade strike-off easy with a 30cm/1 foot extension. The kit includes bracket and mounting hardware necessary to secure one side of the Heavy Duty screed for both the Value and Worldwide versions. Two kits must be ordered if both ends of the screed need to be recessed.
Outrigger
0115715
Outriggers offer a quick and inexpensive way to extend a screed by 30cm/1 foot. They are designed to lengthen the screed at the level of the strike off blade. This Heavy Duty outrigger will fit both Value and Worldwide truss screed versions.
Wall slider
0115716
The wall slider is designed to attach to the end section of the truss screed and makes concrete placement possible against an existing wall with little edge work. The wall slider rests on a narrow rail (L-bracket) that is attached to the wall above the grade of the slab.
Recesser, 1,5ft
0117962
This recessing attachment makes below-grade strike-off easy with a 45 cm/1.5 foot (18 inch) extension. The kit includes bracket and mounting hardware necessary to secure one side of the Heavy Duty screed for both the Value and Worldwide versions. Two kits must be ordered if both ends of the screed need to be recessed.
Outrigger, 1,5ft
0117963
Outriggers offer a quick and inexpensive way to extend a screed by 45cm/18 inches. They are designed to lengthen the screed at the level of the strike off blade. This Heavy Duty outrigger is for use with truss screeds.

Model Guide

100 = 10.0 feet, 50 = 5.0 feet, C = Center section, E = End section, G = High performance engine, H = Heavy-duty model, P = Power section

Model Engine type Horsepower Length x width x height Beam width Height Weight
-
kW hp
mm in
mm in
mm in
kg lb
0115708
HC 100
-
3,1 10.0
355 14
475 18.75
52 115
0130376
HC 25
-
0,76 2.5
355 14
475 19
13 29
0115709
HC 50
-
1,5 5.0
355 14
475 18.75
26 58
0130384
HE 100
-
3.1 10.2
355 14
475 19
55 121
0115713
HE 25
-
0,76 2.5
355 14
475 18.75
16 36
0130383
HE 50
-
1.5 5
355 14
475 19
30 66
0009508
HP 50A
355 14
1,5 4.8
0008293
HPG 100
air-cooled, 4 cycle, single cylinder, gasoline engine Honda
6 8
3,1 10.0
355 14
475 18.75
92 204

Specifications may change due to continuous product development.
* Actual power output may vary due to conditions of specific use.